Verint Nextive S5503 Uživatelská příručka

Procházejte online nebo si stáhněte Uživatelská příručka pro Bezpečnostní kamery Verint Nextive S5503. Verint Nextive S5503 User guide Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 152
  • Tabulka s obsahem
  • ŘEŠENÍ PROBLÉMŮ
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků

Shrnutí obsahu

Strany 1 - Nextiva S1800e Series

Nextiva S1800e SeriesMay 14, 2013User GuideForS1808e and S1816e Series Encoder Firmware Version 2.4 SP9S1801e and S1802e Series Encoder and Decoder Fi

Strany 2

Location Contact Information+ 852 2797 5678Contacting Service and SupportTo request the latest versions of firmware and software or to download otherp

Strany 3

Configuring the Camera TamperingPropertiesThe camera tampering feature is a real-time automated feature that generatesan alarm whenever the camera is

Strany 4 - Contents

Configuring the Motion Detection PropertiesThe S1800e encoders support motion detection on each video input. For eachvideo input, you can configure th

Strany 5

Lower Thresh:The maximum number of macroblocks with motion in aframe to stop an alert. This value must be less than or equal to UpperThresh. The valu

Strany 6

Configuring the Video Output PropertiesThe S1800e decoders support four to six H.264 video streams, displaying up tofour tiles on traditional CCTV mon

Strany 7

Receiver Mode:The number of tiles to display on the monitor. Selectfrom the following:Single:Video from one stream is displayed on the monitor.Quad:

Strany 8

► To set the SNMPproperties1. Start the Web Interface.2. From the tree, select Configuration >SNMP.3. In the SNMP panel, select the Enabled check

Strany 9 - Nextiva Web Interface Help

10. In the User Authentication Type list, select the authentication algorithmfor SNMP requests. You can select from the following:No Authentication:N

Strany 10 - Location Contact Information

edVinCamtampOofAlarmStateNotif trap. This trap is generated if the Out OfFocus status of an input has changed with the following information:[0x00]= N

Strany 11

Setting the Audio Sampling RateExpressed in hertz (Hz), sampling rate is the rate at which samples of ananalog signal are taken in order to be convert

Strany 12 - Summary of Changes

1. Start the Web Interface.2. From the tree, select Configuration >Audio.3. Select the Input Properties tab.4. Set the values for each input:Input

Strany 13 - Revision 5 - June 2011

SafetyAlways observe the following precautions to reduce the risk of injury andequipment damage:The S1800e series devices are for indoor use only.Do n

Strany 14 - Revision 2 - February 2010

► To set the audio encoder properties1. Start the Web Interface.2. From the tree, select Configuration >Audio.3. Select the Encoder Properties tab

Strany 15 - Revision 1- October 2009

► To set the audio output properties1. Start the Web Interface.2. From the tree, select Configuration >Audio.3. Select the Output Properties tab.4

Strany 16

► To set the audio decoder properties1. Start the Web Interface.2. From the tree, select Configuration >Audio.3. Select the Decoder Properties tab

Strany 17 - Hardware Overview

Verint recommends that you activate the Nextiva Onboard Analytics licenseprior to adding the multiport S1800e series encoder to Nextiva VMS. If themul

Strany 18

Configuring Nextiva Onboard AnalyticsOnce activated, you can use Nextiva Onboard Analytics on the four video inputs(1, 2, 5, and 6 on the S1808e) and

Strany 19 - Product Dimension and Weight

Bounding Boxes only: Displays color-coded rectangles around objectsbeing tracked. The following three colors are used:Magenta to track PeopleGreen to

Strany 20 - Multi-Port Devices

NoteVi-System is separate analytics software by Agent Vi. In order for themultiport encoder to work with Vi-System, you must purchase the Vi-Systemsof

Strany 21

Configuring Agent Vi Video AnalyticsOnce activated, you can configure Agent Vi Video Analytics on eight videoinputs and enable or disable the overlay

Strany 22 - Multi-Port Terminal Block

Setting the On-Screen Display for theDecodersOn the S1801e-R and S1801e-R-HD, you can configure the information that isdisplayed on the external monit

Strany 23 - Nextiva Onboard Analytics

5. In the Display Logo list, choose to show the Verint logo on the monitorduring the device start up. Choose from:DisplayedNot Displayed6. In the Tra

Strany 24 - Single- and Dual-Port Devices

Summary of ChangesThis section lists technical updates and new material added to the NextivaV3300 User Guide.Revision 11 - May 2013This is the elevent

Strany 25 - Supported Frame Rates

► To record to the storage device1. Start the Web Interface.2. From the tree, select Configuration >Storage.3. Select one of the following:No reco

Strany 26 - Supported Tile Layout

This chapter discusses how to perform maintenance and troubleshooting taskson the S1800e series devices using SConfigurator or the Web Interface.Addit

Strany 27

Firmware UpgradeFirmware upgrade allows you to install a new firmware of the S1800e devicewhen it becomes available. Updating the firmware allows you

Strany 28 - Supported Audio Formats

5. click Start.6. In the Firmware File Selection dialog box, click Browse and select thecorrect firmware file.7. Click Next to view the verification s

Strany 29 - Video Status LEDs

Performing a Batch Firmware UpdateWith the Nextiva video management software, you can easily update thefirmware for multiple devices in the environmen

Strany 30 - RTSP Support

► To reboot from the front panel1. On device, press Reset.Factory Default SettingsIf after rebooting the device still does not function the way it sho

Strany 31

► To restore the factory default settings using the Web Interface1. Start the Web Interface.2. From the tree, select Administration >Factory Defau

Strany 32 - Dual-Port Devices

The device failed to boot normallyThe power or network connection to the device is lost during a firmwareupgradeA flashing orange (1 sec. intervals) o

Strany 33 - Installing in a Rack

Check the connection between the device and the cameraCheck the camera to ensure that it is transmitting video or that it isfunctioning correctlyCheck

Strany 34 - ► To install in a rack

Verify the cable between the camera and the device. Try another cable tosee if video quality improves.Web status should be checked for lock / unlock s

Strany 35 - Powering the Devices

Revision 8 - March 2012This is the eight edition of the Nextiva S1800e Series User Guide.New FeatureSupport for AgentVi Video Analytics on the multipo

Strany 36 - ► To power the devices

AppendixAChapter A: Specification and ConfigurationTechnical Specification 131Factory Default Configuration 137

Strany 37 - Connecting Analog Cameras

Technical SpecificationThe following table presents the technical specifications for the S1800e seriesdevices:S1808e,S1808e-A,S1816e,S1816e-A,S1816e-S

Strany 38 - Connecting Network Cables

S1808e,S1808e-A,S1816e,S1816e-A,S1816e-SPand S1816e-SRS1801eS1802eS1801e-RS1801e-R-HDS1816e-SP:D1/15 fps(H.264),CIF/15fps(MPEG-4) on allchannelssimult

Strany 39 - Connecting a Serial Device

S1808e,S1808e-A,S1816e,S1816e-A,S1816e-SPand S1816e-SRS1801eS1802eS1801e-RS1801e-R-HDmonitorTilesdisplayoptions:1×1,2×2options: 1 ×1,2×2 or 3 × 2Netwo

Strany 40 - ► To connect RS-232 devices

S1808e,S1808e-A,S1816e,S1816e-A,S1816e-SPand S1816e-SRS1801eS1802eS1801e-RS1801e-R-HDNoteThe S1816e-SRdoes not have aUSBport.32 GB (SDcard notinclude

Strany 41

S1808e,S1808e-A,S1816e,S1816e-A,S1816e-SPand S1816e-SRS1801eS1802eS1801e-RS1801e-R-HD(1/8in.(3.5mm))S1816e-A: 16stereo jacks(1/8in.(3.5mm))PowerSupply

Strany 42 - Connecting RS-485 Devices

S1808e,S1808e-A,S1816e,S1816e-A,S1816e-SPand S1816e-SRS1801eS1802eS1801e-RS1801e-R-HDFirmware Embedded Linux-based operating systemManagementConfigura

Strany 43 - Connecting Audio Output

S1808e,S1808e-A,S1816e,S1816e-A,S1816e-SPand S1816e-SRS1801eS1802eS1801e-RS1801e-R-HDPS1281: 19-inchrack mountablepower supply forup to 10multiportdev

Strany 44 - ► To connect audio outputs

Type ConfigurationResolution: 4CIFTarget frame rate: 30 fps(NTSC) / 25 fps (PAL)Target bit rate: 1200 kbpsMinimum quantizer: 14Maximum quantizer: 24En

Strany 45 - Multiport Devices

Index11 GbpsLink Speed 87, 8910 MbpsLink Speed 87, 89100 MbpsLink Speed 87, 8922CIFResolutionConfiguring Encoder 76, 95, 9844CIFResolutionConfiguring

Strany 46

S1801e, S1801e-R or S1801e-R-HD, S1802e, S1808e-A, S1816e-A:Support for μ-LAW audio codec.S1801e-R or S1801e-R-HDMI:Support for decoding video from Ne

Strany 47

Input Type 109Authentication TypeMD5 AuthenticationSNMP Setting 80, 106No AuthenticationSNMP Setting 80, 106PasswordSNMP Setting 80, 106SHA Authentica

Strany 48

Community NameSNMP Setting 80, 105Compression ModeConfiguring Audio Input 110, 112Configuring Encoder 76, 95, 98configurationdefault 127, 137Configuri

Strany 49

CIF 76, 95, 98D1 76, 95, 98Configuring IP Address 59, 85Configuring Motion Detection 101Lower Thresh 102Mask 101Mask State 101Nb Frames 102Upper Thres

Strany 50

default username 84DES EncryptionSNMP Setting 80, 106Device Discovery 58DevicesDual-Port 17Multi-Port 19-20, 22Single-Port 17DHCPConfiguringDefault Ga

Strany 51 - Connecting RS-232 Devices

Rate Control Mode 76, 95, 98Constant Bit Rate 76, 95, 98Constant Frame Rate 76, 95, 98Resolution 76, 95, 982CIF 76, 95, 984CIF 76, 95, 98CIF 76, 95, 9

Strany 52

InputAudio 43, 54Input TypeConfiguring Audio Input 109Installing Flat Surface 33, 46Installing Rack 33, 47Intra IntervalConfiguring Encoder 76, 95, 98

Strany 53

ModeCompressionConfiguring Encoder 76, 95, 98Motion DetectionConfiguing 101ConfiguringLower Thresh 102Mask 101Mask State 101Nb Frames 102Upper Thresh

Strany 54

passwordChanging 84default 84PersistenceConfiguring Camera Tampering 100pinoutserial port 39, 50Primary Trap Destination AddressSNMP Setting 79, 105Pr

Strany 55

CIF 76, 95, 98D1 76, 95, 98resolution, video 24, 27RulesCreating Video Analytics 23SS1816e-SP EncoderConfiguring 70SaturationConfiguring Video Input 9

Strany 56 - Configuration

Backup Trap Destination Address 79, 105Community Name 80, 105Primary Trap Destination Address 79, 105Privacy Password 80, 106Privacy Protocol 80, 106A

Strany 57 - Setting SConfigurator

Revision 1- October 2009This is the first edition of the Nextiva S1800e Series User Guide.What's New8 or 16-video input encoders with up to tripl

Strany 58 - Discovering Devices

Setting The Vsip 78, 81-83, 104, 108-111shipment list 33, 46Single-Port Devices 17SNMPSetting 78, 104Authentication Type 80, 106MD5 Authentication 80,

Strany 59 - IP Address Configuration

Upper ThreshConfiguring Motion Detection 101User NameSNMP Setting 80, 105usernamedefault 84UsingAgentVi Video Analytics 117Using Audio 28Using Nextiva

Strany 60 - Setting a Static IP Address

Video StandardSettingNTSC 73, 93PAL 73, 93For more information, please visit us at http://www.verint.com/solutions/video-situation-intelligence/index.

Strany 61 - ► To set a static IPaddress

The Nextiva® encoders are enterprise-class, H.264 enabled video encodersdesigned for large-scale, geographically distributed operations. These powerfu

Strany 62 - Configuring the Serial Ports

Hardware OverviewThe ® S1800e series devices consist of the following models:Single and Dual Port devicesS1801eS1801e-PoES1801e-RS1801e-R-HDMIS1802eMu

Strany 63

The S1800e series decoders (S1801e-R and S1801e-R-HD)are designed for usewith all S1800e series single- and multi-port encoders and the S5000 IPCamera

Strany 64

1. Video input2. Audio input and output3. Video output4. HDMIoutput5. One RJ-45 network connector6. Terminal Block7. One MicroSD card slot (Only avai

Strany 66 - Using SConfigurator

Multi-Port DevicesThe S1800e series multi-port encoders delivers high-resolution images for bothrecording and live video viewing. The Nextiva S1808e,

Strany 67

S1816e RearS1816e-SPRearS1816e-SR RearDescription1. Two RJ-45 Network connectors (One RJ-45 Network connector on theS1816e-SR model)2. Video Status L

Strany 68

Multi-Port Terminal BlockS1808e Terminal BlockS1816e and S1816e-SP Terminal BlockS1816e-SRTerminal BlockDescriptionChapter 1: S1800e Series Overview©

Strany 69

1. One 12V DCinput2. One RS-2323. Relay outputTwo on the S1808eFour on the S1816eOne on the S1816e-SR4. RS 422/4855. Dry contacts8 on the S1808e16 on

Strany 70 - S1816e-SP or S1816e-SR

SecurityEvery S1800e series device comes with a unique SSL (Secure Sockets Layer)certificate for securing its IP link. SSL is a commonly used protocol

Strany 71

Supported Frame RatesThe following table lists the performance that each video encoder on theS1801e and S1802e encoders can achieve with the H.264 com

Strany 72 - Setting the Video Standard

Supported Tile LayoutThe following table lists the supported video decoding resolution on each tile byeach mode on the S1801e-R and S1801e-R-HD.Tiles1

Strany 73 - ► To set the video standard

Encoders 1 and 2 are H.264 and Encoder 3 is MPEG4. You can customize eachencoder to meet the system requirements in terms of frame rate andresolution.

Strany 74 - Video Profile

Supported Audio FormatsThe S1801e, S1802e, S1808e-A, S1816e-A, S1801e-R and S1801e-R-HDsupports bi-directional audio: audio input and output. Audio in

Strany 75

LED Pattern DescriptionFlashing green (0.2sec. intervals)The firmware has started, the encoder is connected tothe network, and serial data is transmit

Strany 76

Copyright Notice© 2013 Verint Systems Inc. All Rights Reserved Worldwide.Confidential and Proprietary Information of Verint Systems Inc.All materials

Strany 77

LED Pattern DescriptionFlashing green-red (1 sec.intervals)The encoder is undergoing a firmware update.For multiportencoders:Steady orangeFor single/d

Strany 78

Configuring the Input/Output TerminalsThe rear panel of the S1800e series devices has 1, 2, 8 or 16 dry contact inputsand 1, 2 or 4 relay output termi

Strany 79

This chapter describes the installation and configuration steps you need toperform to prepare the S1800e series devices for operation.CautionThe S1800

Strany 80

Package ContentsEach installation kit contains the following:One S1801e, S1801e-PoE, S1802e, S1801e-R or S1801e-R-HD deviceOne set of rack-mount brack

Strany 81

► To install in a rack1. Remove the two screws from the S1800e series device.2. Screw the S1800e series device to the rackmount plate using 5 in-lb (0

Strany 82

N-m) force with the provided screws.3. Slide the device into the 3U mounting space in the rack cabinet.4. Secure the device to the rack cabinet using

Strany 83

► To power the devices1. Remove the terminal block plug from the rear of the device.2. Verify the polarity of each wire from the power supply accordin

Strany 84

Powering the S1801e-POEThe S1801e and S1802e encoders consumes up to 5W of power, while theS1801e-R and S1801e-R-HDMI consumes up to 4W of power.► To

Strany 85

► To connect analog cameras1. Connect the video cables from the analog cameras to the BNC connectors onthe rear of the device.Connecting Network Cable

Strany 86 - ► To set a DHCPaddress

Connecting a Serial DeviceRS-232, RS-422 and RS-485 are communication standards between a DataTerminal Equipment (DTE) and a Data Circuit-terminating

Strany 87

ContentsPreface 8Nextiva Web Interface Help 9Documentation and Firmware 9Contacting Verint 9Contacting Service and Support 10Safety 11Summary of Chang

Strany 88

► To connect RS-232 devices1. Remove the terminal block plug from the rear of the device.2. Connect a twisted pair cable to the terminal block plug as

Strany 89

► To connect RS-422/485 four-wires devices1. Remove the terminal block plug from the rear of the device.2. Connect a twisted pair cable to the termina

Strany 90

Connecting RS-485 DevicesIn order to connect an RS-485 device to the S1800e, you will need to create aData+ and a Data- signal from the existing Tx an

Strany 91

Connecting Audio InputsThe S1801e and S1802e supports bi-directional audio: audio input and output.Audio input allows you to capture audio signals fro

Strany 92

► To connect audio outputs1. Insert the cable of the speaker into Audio Out audio output connector on therear.2. Connect the other end of the connecto

Strany 93

This chapter describes the installation and configuration steps you need toperform to prepare the S1800e series devices for operation.CautionThe S1800

Strany 94

Package ContentsEach installation kit contains the following:One S1808e, S1808e-A, S1816e, S1816e-A, S1816e-SP or S1816e-SR deviceOne set of rack-moun

Strany 95

Installing in a RackThis section explains how to install the device in a rack.► To install in a rack1. Align the mounting brackets with the holes on t

Strany 96

Powering the Multiport DevicesYou can use the PS1261 or any other certified power supply to connect to theS1800e series devices. If you plan on using

Strany 97

5. Connect the power supply to an outlet or UPS.6. If required, connect the serial ports of the S1800e device to a PTZ camera.NoteIf you are using the

Strany 98

Supported Resolution 24Supported Frame Rates 25Supported Decoding Resolution and Tile Layout 25Supported Tile Layout 26Multiport Supported Resolutions

Strany 99

Connecting Network CablesThe primary network interface (LAN-1) on the S1800e series is for the mainconnectivity to the LAN.The secondary network inter

Strany 100 - Properties

Connecting RS-232 DevicesThe RS-232 standard is used in some analog cameras and computer serialports. Before connecting the S1800e series device to a

Strany 101

Connecting RS-422/485 Four-WiresMost target devices (keyboards, PTZ cameras, monitors) use the RS-422/485protocol for communication.Using a twisted pa

Strany 102

Connecting RS-485 DevicesIn order to connect an RS-485 device to the S1800e, you will need to create aData+ and a Data- signal from the existing Tx an

Strany 103

Connecting Audio InputsThis section explains how to connect audio devices to the S1800e multiportencoders. Theaudio-in connectors support two audio-mo

Strany 104 - Setting the SNMP Properties

NoteThe S1816e-SPand S1816e-SR models do not support audio out.► To connect audio outputs1. Insert the cable of the speaker into Audio Out audio outp

Strany 105 - ► To set the SNMPproperties

Once you have connected all the equipment to the device, you can beginconfiguring the device to ensure that it can communicate with the attacheddevice

Strany 106 - Viewing MIB Information

Setting SConfiguratorBefore you can use SConfigurator to discover devices on the network, you needto set the initial parameters.► To set SConfigurator

Strany 107 - Audio Properties

NoteVSIP ports 9541, 65500, and those under 1024 are reserved and shouldnever be used, not even for serial port, video, or audio communication.The max

Strany 108

In APIPA mode, the Unit Name column in the Units box displays Unknownand the first two octets of the IP address in the Address column is 169.254.Use t

Strany 109

Setting a DHCPIP Address 60Setting a Static IP Address 60Configuring the Serial Ports 62Configuring the RS-232 Serial Port Using SConfigurator 62Conf

Strany 110

Setting a DHCPIP AddressThe S1800e series devices automatically obtains the IP network configurationfrom a DHCP server. Use this procedure if you are

Strany 111

► To set a static IPaddress1. Start SConfigurator.2. Select the Units tab, then click Discover.3. Select the Nextiva device, and click Configure.4. I

Strany 112

Configuring the Serial PortsOnce the serial equipment is connected to the device, you need to ensure thatboth devices can communicate with each other.

Strany 113

► To configure the RS-232 portConfiguring the RS-232 Serial Port Using SConfigurator63 © 2013 Verint Video Systems Inc.

Strany 114

1. Start SConfigurator.2. Select the Units tab, then click Discover.3. Select the Nextiva device, and click Configure.4. In the tree view, click Unit

Strany 115

5. Select one of the following:(Single- and Dual-Port devices) RS-232/422/485.(Multiport devices) RS-232.6. In the Baud Rate list, select the data rat

Strany 116 - ► To activate Agent Vi

8. In the Stop bits list, select the stop bits used by the serial equipment. Stopbits let the receiver know that the byte being transmitted has ended.

Strany 117 - ► To configure Agent Vi

► To configure the RS-422/485 portConfiguring the RS-422/485 Serial Port Using SConfigurator67 © 2013 Verint Video Systems Inc.

Strany 118 - Decoders

1. Start SConfigurator.2. Select the Units tab, then click Discover.3. Select the Nextiva device, and click Configure.4. In the tree view, click Unit

Strany 119

5. Select one of the following:(Single- and Dual-Port devices) RS-232/422/485.(Multiport devices) RS-422/485.6. In the Baud Rate list, select the data

Strany 120

Upgrading Using SConfigurator 122Upgrading Using the Web Interface 123Performing a Batch Firmware Update 124Device Reboot 124Rebooting the Device Usin

Strany 121 - Troubleshooting the Device

8. In the Stop bits list, select the stop bits used by the serial equipment. Stopbits let the receiver know that the byte being transmitted has ended.

Strany 122 - Firmware Upgrade

► To configure the H.264 encoding mode1. Start SConfigurator.2. Select the Units tab, then click Discover.3. Select the Nextiva device, and click Conf

Strany 123

Setting the Video StandardThe S1800e series device can run in one of two video standards (NTSC or PAL)and you can use different standards when deployi

Strany 124 - Device Reboot

► To set the video standard1. Start SConfigurator.2. Select the Units tab, then click Discover.3. Select the Nextiva device, and click Configure.4. In

Strany 125 - Factory Default Settings

Video ProfileVideo Profiles define both the quality of the video images and the storage andbandwidth requirements of the video files. All Video Profil

Strany 126 - Troubleshooting

► To configure the devcie video properties1. Start SConfigurator.2. Select the Units tab, then click Discover.3. Select the Nextiva device, and click

Strany 127 - Losing Connection to a Camera

NoteTo maintain the video frame rate, you should set the maximum quantizerto 31. If the quality of each frame is more important, you should reducethe

Strany 128 - Quality of the Video is Bad

Configuring the Input PropertiesThe number of video inputs varies depending on the device. For each videoinput, you can enhance the video image by adj

Strany 129

Saturation:This refers to the intensity of the colors in the image. Thevalues range from -128 to 127.6. Click OK.7. Click Exit.Setting the SNMP Prope

Strany 130 - Appendix

► To set the SNMPproperties1. Start SConfigurator.2. Select the Units tab, then click Discover.3. Select the Nextiva device, and click Configure.4. I

Strany 131 - Technical Specification

PrefaceThe Nextiva® S1800e User Guide presents information and procedures oninstalling, configuring, and using the Nextiva encoders and decoders.The W

Strany 132

10. In the Community Name box, type the name of the group where you wantthe edge device to be a member.NoteThe Edge device will only respond to reques

Strany 133

CodecSamplingFrequencyBits perSampleBitratePCM (nocompression)8 kHz 16bits/data 28 kbits/sec(8kHz)G.711/μ-Law (8bits)8 kHz 14 bitssigned/data64 kbits/

Strany 134

Setting the Audio Encoder PropertiesThe S1801e, S1802e, S1808e-A and S1816e-A supports bi-directional audio:audio input and output. Audio input allows

Strany 135

Setting the Audio Decoder PropertiesThe audio output properties allow you to set the Gain to increase the amplitudeof the input signal.► To set the au

Strany 136

Once you have connected all the equipment to the device, you can beginconfiguring the device to ensure that it can communicate with the attacheddevice

Strany 137 - Factory Default Configuration

IP Address ConfigurationBy default, all S1800e series devices are Dynamic Host Configuration Protocol(DHCP ) enabled. If you have a DHCP server, the d

Strany 138 - Type Configuration

► To set a DHCPaddress1. Start the Web Interface.2. From the tree, select Configuration >Network.3. In the Hostname box, type a unique name for t

Strany 139 - Gain 109, 111

7. In the Ethernet Adapter 1 tab:a. In the Link Speed list, select the speed and mode of the network:Auto detect:The unit will automatically detect t

Strany 140 - Input Type 109

► To set a static IPaddress1. Start the Web Interface.2. From the tree, select Configuration >Network.3. In the Hostname box, type a unique name

Strany 141

7. In the Ethernet Adapter 1 tab:a. In the Link Speed list, select the speed and mode of the network:Auto detect:The unit will automatically detect t

Strany 142

Nextiva Web Interface HelpThe Web Interface User Help presents the information and procedures forconfiguring the S5503 PTZIPCameras and Nextiva® S18

Strany 143

NoteThe Ethernet Adapter 2 tab corresponds to LAN 2 on the S1808e, S1808e-A,S1816e, S1816e-A and S816e-SPencoders, and is used by support fordebuggin

Strany 144

► To configure the RS-232 port1. Start the Web Interface.2. From the tree, select Configuration >Serial Port.3. Select one of the following:(Singl

Strany 145

► To configure the RS-422/485 port1. Start the Web Interface.2. From the tree, select Configuration >Serial Port.3. Select one of the following:(S

Strany 146

National Television Standards Committee (NTSC) is the standard that is used inmost of the Americas, a number of South American countries, and some Asi

Strany 147

4. Click Yes to make the changes.5. Click Apply.6. Click OK to reboot the Edge device.Configuring the Encoder PropertiesFor each video input, the S180

Strany 148

Quantizer (Minimum and Maximum):The process of safelydiscarding information from a video without a significant loss in visualquality. Using a higher

Strany 149

MJPEG.NoteFor devices running analytics and the S1816e-SP and S1816e-SRmodels running in single or legacy mode, only two streams areavailable. In thi

Strany 150

► To configure the encoder properties1. Start the Web Interface.2. From the tree, select Configuration >Video.3. From the Encoder Properties tab,

Strany 151

Intra Interval:The frequency at which a complete video frame (I-frame) is sent by the device. The available values are in the 0 – 1000range. Zero ind

Strany 152

Configuring the Input PropertiesThe number of video inputs varies depending on the device. For each videoinput, you can enhance the video image by adj

Komentáře k této Příručce

Žádné komentáře